ccomley
03-11-2009, 11:37 AM
I post this coz *I* can never find my notes on how to do it when I'm in a hurry. No comments needed unless you think I'm doing something long-winded or even wrong. :)
There is no auto-provision for the Snom M3 system (as of this date).
To set up an M3 on a Quadro
1) Go Telephony / Line Settings, find the IP Line for the extension you want (normally the next free one!) and edit it.
2) In the edit panel, change the type from Inactive to SipPhone. Select model "OTHER", dont' fill in the MAC address (It won't let you) and change the password to something you know. e.g. 123456. Save.
3) Browse to the M3's web GUI (It'll have grabbed an IP via DHCP - probabyl calling itself "SIP Handset" or similar. Password is admin / admin.
4) Click on Identity1. Set up the page as follows:-
Server is local = yes.
Display name = Extension 123 (or "alf" or whatever).
Account = locext123 (should match user name given at 2 above.)
Password - 123456 (again, matches what you set at 2 above.)
Account name = Identity 1 (shouldn't need to change this).
Account Mailbox Name = locext123@172.30.0.1 (IP address of your PBX of course).
Account Mailbox Number = leave Blank
Registrar = <ip address of your PBX)
Outbound Proxy = <ip address of your PBX)
Authentication User Name = locext123
Server Port = 5060
Outbound Proxy Port = 5060
Re-Reg time = 600
THE REMAINING entries you can leave as they default and just Save.
NOTE
YOU MAY FIND that you need to force the system to reboot to make te new settings kick in. 've had a handset saying "Auth failure" for ages even having done a "Base station reset" from the handset but once I select "Reboot" from the bottom of the Identit1 GUI page, it seems to kick in OK.
Finally - check the Telephony settings, that the handset you are using is allowed to use the Ident that you just set up. Users with more than one handset and/or more than one Identity will be able to see what's going on here fairly easily. Default *should* be enabled for all.
There is no auto-provision for the Snom M3 system (as of this date).
To set up an M3 on a Quadro
1) Go Telephony / Line Settings, find the IP Line for the extension you want (normally the next free one!) and edit it.
2) In the edit panel, change the type from Inactive to SipPhone. Select model "OTHER", dont' fill in the MAC address (It won't let you) and change the password to something you know. e.g. 123456. Save.
3) Browse to the M3's web GUI (It'll have grabbed an IP via DHCP - probabyl calling itself "SIP Handset" or similar. Password is admin / admin.
4) Click on Identity1. Set up the page as follows:-
Server is local = yes.
Display name = Extension 123 (or "alf" or whatever).
Account = locext123 (should match user name given at 2 above.)
Password - 123456 (again, matches what you set at 2 above.)
Account name = Identity 1 (shouldn't need to change this).
Account Mailbox Name = locext123@172.30.0.1 (IP address of your PBX of course).
Account Mailbox Number = leave Blank
Registrar = <ip address of your PBX)
Outbound Proxy = <ip address of your PBX)
Authentication User Name = locext123
Server Port = 5060
Outbound Proxy Port = 5060
Re-Reg time = 600
THE REMAINING entries you can leave as they default and just Save.
NOTE
YOU MAY FIND that you need to force the system to reboot to make te new settings kick in. 've had a handset saying "Auth failure" for ages even having done a "Base station reset" from the handset but once I select "Reboot" from the bottom of the Identit1 GUI page, it seems to kick in OK.
Finally - check the Telephony settings, that the handset you are using is allowed to use the Ident that you just set up. Users with more than one handset and/or more than one Identity will be able to see what's going on here fairly easily. Default *should* be enabled for all.